HEAT RATE SYSTEM ANALYSIS IN THE STEAM POWER PLANT IN NIITANASA USING ENVIRONMENTALLY FRIENDLY LOW-CALORIE FUELS (REVISI)
DOI:
https://doi.org/10.20319/mijst.2020.61.5870Keywords:
Heat Rate, Coal, Steam, Electric, FuelAbstract
The heat rate in a steam power plant is very important to know because it involves the amount of energy supply needed to produce electricity. This is done to determine the heat energy input from fuel needed in an electric energy. The purpose of this research is to analyze the heat rate needed in a steam power plant. The method used is the direct method, the required input is Gross kWh, Net kWh, coal fuel use, calorific value of the fuel. The type of fuel used is low calorie type of lignite. The results of the Gross Heat rate in January were seen 4,323.98 kcal / kWh while the Net Heat rate was 5,010.97 kcal / kWh. In December the Gross Heat rate was 4,141.72 kcal / kWh while the Net Heat rate was 4,992.96 kcal / kWh. This value is relatively high at a capacity of MW 100 MW.
References
Aljundi, I. H. (2009).Energy and exergy analysis of a steam power plant in Jordan.Applied thermal engineering, 29(2-3), 324-328. https://doi.org/10.1016/j.applthermaleng.2008.02.029
Babcock & Wilcox Company. (1923). Steam: its generation and use. Babcock & Wilcox Company.
Callister, W. D. Fundamental of materials science and engineering/an interactive e. text, 2001, John Willey & Sons.Inc., New York.
Chapelle, D., & Bathe, K. J. (2011).Towards the formulation of effective general shell elements.In The Finite Element Analysis of Shells-Fundamentals (pp. 315-363).Springer, Berlin, Heidelberg. https://doi.org/10.1007/978-3-642-16408-8_8
Evans, R. L. (2007). Fueling our future: an introduction to sustainable energy.Cambridge University Press. https://doi.org/10.1017/CBO9780511807015
Fleisher, P. (2002). Relativity and Quantum Mechanics: Principles of Modern Physics. Twenty-First Century Books.
Heinz, B., & Singh, M. (2009).Steam Turbines–Design, Applications and Rerating.McGraw-Hill, New York.
Kanoglu, M., Dincer, I., & Rosen, M. A. (2007). Understanding energy and exergy efficiencies for improved energy management in power plants.Energy Policy, 35(7), 3967-3978. https://doi.org/10.1016/j.enpol.2007.01.015
Kim, J. Y., & Ghajar, A. J. (2006). A general heat transfer correlation for non-boiling gas–liquid flow with different flow patterns in horizontal pipes. International Journal of Multiphase Flow, 32(4), 447-465. https://doi.org/10.1016/j.ijmultiphaseflow.2006.01.002
Leĭzerovich, A. S. (2008). Steam turbines for modern fossil-fuel power plants. The Fairmont Press, Inc..
Naphon, P., & Wongwises, S. (2005). A study of the heat transfer characteristics of a compact spiral coil heat exchanger under wet-surface conditions. Experimental thermal and fluid science, 29(4), 511-521. https://doi.org/10.1016/j.expthermflusci.2004.07.002
Pavelka, P., Hunady, R., &Hagara, M. (2016). The Influence of Preload on Modal Parameters of A Cantilever Beam. American Journal of Mechanical Engineering, 4(7), 418-422.
PLTU, P. O. (2018). Data Ikhtisiar PLTU Nii Tanasa. Kendari: PLN Kendari.
Purnomo, J., & EFFENDY, M. (2018).AnalisaPengaruh Load Capacity Pembangkit Listrik Tenaga Uap Tanjung Awar-Awar 350 Mw Terhadap Efisiensi Turbin Generator QFSN-350-2 UNIT 1. Jurnal Pendidikan Teknik Mesin, 7(3).
Stølen, S., Grande, T., & Allan, N. L. (2004). Chemical thermodynamics of materials.Macroscopic and Microscopic Aspects. https://doi.org/10.1002/0470092688
Wu, C. (2007). Thermodynamics and heat powered cycles: a cognitive engineering approach. Nova Publishers.
Downloads
Published
How to Cite
Issue
Section
License
Copyright of Published Articles
Author(s) retain the article copyright and publishing rights without any restrictions.
All published work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
