COMPARISON OF THE EFFECTS OF REACTION PARAMETERS ON COLD FLOW PROPERTIES OF BIODIESE

Authors

  • Ceyla ÖZGÜR Department of Automotive Engineering, Çukurova University, Adana, Turkey
  • Erdi TOSUN Department of Mechanical Engineering, Çukurova University, Adana, Turkey
  • Tayfun ÖZGÜR Department of Automotive Engineering, Çukurova University, Adana, Turkey

DOI:

https://doi.org/10.20319/mijst.2017.33.6271

Keywords:

Linseed Oil, Biodiesel, Transesterification, Reaction Parameters, Cold Flow Properties

Abstract

Biodiesel is biodegradable, renewable and nontoxic fuel source instead of petroleum fuel. Biodiesel has bad cold flow properties. The aim was to specify the optimum reaction parameters and obtain minimum cold flow properties. Transesterification method was preferred as the biodiesel production method. Reaction of transesterification is affected by diverse reaction parameters like as catalyst amount, molar ratio of alcohol to oil, time of reaction and temperature of reaction. In this experimental study, the impacts of operation parameters on cold flow properties of linseed oil biodiesel was compared. In production process potassium hydroxide (KOH) was chosen as catalyst and ethanol was used as alcohol. The impacts of catalyst amount (0.3-1.1 wt%), molar ratio of ethanol to oil (4:1-8:1), reaction time (45-105 min) and reaction temperature (50-65 ºC) was investigated. The minimum cold flow property values were obtained at 0.5% catalyst concentration, 7:1 molar ratio of ethyl alcohol to oil, 90 min of reaction time, 65ºC of reaction temperature. The lowest pour point, cloud point and cold filter plugging point of linseed biodiesel were found -10 ºC, -3 ºC, and -8 ºC, respectively at optimum reaction parameters.

References

Abubakar, H.G., Abdulkareem, A.S., Jimoh., A., Agbajelola, O.D., Okafor, J.O. & Afolabi, E.A. (2016). Optimization of biodiesel production from waste cooking oil. Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, 38 (16), 2355–2361. https://doi.org/10.1080/15567036.2015.1040899

Ayetor, G.K., Sunnu, A. & Parbey, J. (2015). Effect of biodiesel production parameters on viscosity and yield of methyl esters: Jatropha curcas, Elaeis guineensis and Cocos nucifera. Alexandria Engineering Journal, 54, 1285-1290. https://doi.org/10.1016/j.aej.2015.09.011

Boz, N. & Sunal, O. (2009). Biodiesel production from canola oil over zinc oxide upported catalysts. J. Fac. Eng. Arch. Gazi Univ., 24, 389-395.

Buyuk, N. & Ozgur, T. (2016). Cold flow and fuel parameters of palm oil biodiesel. Journal of Çukurova University Science and Engineering, 34 (2), 11-20.

Dias, J.M., Araujo, J.M., Costa, J.F., Alvim-Ferraz, M.C.M. & Almeida, M.F. (2013). Biodiesel production from raw castor oil. Energy, 53, 58-66. https://doi.org/10.1016/j.energy.2013.02.018

Ivana, B.B.I., Stamenkovic, O.S. & Veljkovic, V.B. (2012). Biodiesel production from non-edible plant oils. Renewable and Sustainable Energy Reviews, 16, 3621–3647. https://doi.org/10.1016/j.rser.2012.03.002

Kafuku, G. & Mbarawa, M. (2010). Alkaline catalyzed biodiesel production from moringa oleifera oil with optimized production parameters. Applied Energy, 87, 2561–2565. https://doi.org/10.1016/j.apenergy.2010.02.026

Kılıç, M., Uzun, B.B., Pütün, A.E. & Pütün, E. (2013). Optimization of biodiesel production from castor oil using factorial design. Fuel Processıng Technology, 111, 105-110. https://doi.org/10.1016/j.fuproc.2012.05.032

Kumar, N., Soni, S.L., Sharma, D. & Srivastava, Kumar, A. (2016). Performance evaluation and emission analysis of variable compression ratio direct injection diesel engine. Matter: International Journal of Science and Technology, 2, 32-47.

Lavanya, C., Murthy, I.Y.L.N., Nagaraj, G. & Mukta, N. (2012). Prospects of castor (Ricinus communis L.) genotypes for biodiesel production in India. Biomass and Bioenergy, 39, 204-209. https://doi.org/10.1016/j.biombioe.2012.01.008

Rasimoglu, N. & Temur, H. (2014). Cold flow properties of biodiesel obtained from corn oil. Energy, 68, 57-60. https://doi.org/10.1016/j.energy.2014.02.048

Suh, H.K. & Lee, C.S. (2016). A review on atomization and exhaust emissions of a biodiesel-fuelled compression ignition engine. Renewable Sustainable Energy Rev., 58, 1601-1620. https://doi.org/10.1016/j.rser.2015.12.329

Swaminathan, C. & Sarangan, J. (2012). Performance and emission characteristics of a CI engine fuelled with biodiesel (fish oil) with DEE as additive. Biomass and Bioenergy, 39, 168-174. https://doi.org/10.1016/j.biombioe.2012.01.001

Takase, M., Zhao, T., Zhang, M., Chen, Y., Liu, H., Yang, L. & Wu, X. (2015). An expatiate review of neem, jatropha, rubber and karanja as multipurpose non-edible biodiesel resources and comparison of their fuel, engine and emission properties. Renewable and Sustainable Energy Reviews, 43, 495–520. https://doi.org/10.1016/j.rser.2014.11.049

Tuccar, G., Tosun, E., Ozgur, E. & Aydın, K. (2014). Diesel engine emissions and performance from blends of citrus sinesis biodiesel and diesel fuel. Fuel, 132, 7 – 11. https://doi.org/10.1016/j.fuel.2014.04.065

Uludamar, E., Karaman, V., Yıldızhan, Ş. & Serin, H. (2016). Improvement of density, viscosity and cold flow properties of palm oil biodiesel by alcohol addition. International Journal of Engineering Technologies, 2, 64-67. https://doi.org/10.19072/ijet.79988

Yadav, B.K., Soni, S.L., Sharma, D. & Sharma, P.K. (2017). Performance and emission analysis of constant speed SI engine operated on hythane (HCNG). Matter: International Journal of Science and Technology, 3, 64-79.

Yang, L., Takase, M., Zhang, M., Zhao, T. & Wu, X. (2014). Potential non-edible oil feedstock for biodiesel production in Africa: A survey. Renewable and Sustainable Energy Reviews, 38, 461–477. https://doi.org/10.1016/j.rser.2014.06.002

Downloads

Published

2017-11-17

How to Cite

ÖZGÜR, C., TOSUN, E., & ÖZGÜR, T. (2017). COMPARISON OF THE EFFECTS OF REACTION PARAMETERS ON COLD FLOW PROPERTIES OF BIODIESE. MATTER: International Journal of Science and Technology, 3(3), 62–71. https://doi.org/10.20319/mijst.2017.33.6271